My Ex droped her Phone and it had Spider Webs all accross. Her Provider send it in to see what it would cost to fix. The Phone also would stop working correctly in the middle of calls.
It turns out buying a new one would have come cheaper atleast thats what came back as a answear.
So I decided to bite the apple and try replacing the Screen myself. My Ex was not happy because she thought with the second Problem it is not worth the effort to fix the Screen and maybe loose everything. My reasoning was that when the Spider Web Screen touches the Digitizer it will react strangely. So I went ahead and searched the web on how to do it. I ordered a Screen for $9 on ebay (free shipping) which came with a couple of Tools. More on those later.
One of the first Problems I found was that all instructions that I found showed the beginning and the end. But in the middle how the phone will look like when the glass is finaly taken off, I was unable to find much Information about it. Also doing it Redneck style without Special liquids and or a heat guns was no where to be found.
I decided to just try it. Disasembly is well documented and easy enough to do on this device. Atleast to the Point where most electronics are removed so that you can apply heat without too much problems. I decided on using a blow dryer to heat up the Display. I layed the Blow Dryer on the Counter turned it on and Held the phone up to it. Thinking if my fingers get too hot chances are it is too hot for the Display too.. :) Might be a little incaccurate to read the temperature like that but hey it worked. But soon after I started to remove the first pieces of broken glass I ran into Problems.
As per instructions I found, I put a Piece of tape accros the Screen so that the individuall pieces stayed ogether. That did not work at all for me. It just made the individual pieces push against the valuable digitizer below it. My next Problem was that the Tools that came with the replacement glass, especially the Little plastic Tools did not hold up to the Job und the tip was soon useless. I had to Switch to a Raizor blade. A couple of times I sliped and hit the Digitizer. Thinking oh well I guess I Need to get a new one. Luckely on the end it all worked out much better then I would have hoped. The left over glue I rubbed mostly off with my finger which worked out nicely. To clean it completely from ist glue took some time. The black rubber allong the side of the phone allso suffered. You might want to look out that that does not get riped out completely. I had enough left over so that the glass would sit on it good enough luckely.
Take a look at these Pictures and remember it works perfectly again for $9. While it is not for everyone to seperate a Glass from a Digitizer it is acctualy less fragile as you might think. The third Picture Shows you how it looked with all the scuff marks from taking off the glass. You can still see a few little marks on the end but hard to notice and much better then before. I am sure next time I will be more carefull and use the blade from the beginning on.
I got more Pictures and will improve this Thread for others that have to go through it. Feel free to PM me if you have any Questions. A list of other resources will also be included. This is only to explain and Show the bare state.
It turns out buying a new one would have come cheaper atleast thats what came back as a answear.
So I decided to bite the apple and try replacing the Screen myself. My Ex was not happy because she thought with the second Problem it is not worth the effort to fix the Screen and maybe loose everything. My reasoning was that when the Spider Web Screen touches the Digitizer it will react strangely. So I went ahead and searched the web on how to do it. I ordered a Screen for $9 on ebay (free shipping) which came with a couple of Tools. More on those later.
One of the first Problems I found was that all instructions that I found showed the beginning and the end. But in the middle how the phone will look like when the glass is finaly taken off, I was unable to find much Information about it. Also doing it Redneck style without Special liquids and or a heat guns was no where to be found.
I decided to just try it. Disasembly is well documented and easy enough to do on this device. Atleast to the Point where most electronics are removed so that you can apply heat without too much problems. I decided on using a blow dryer to heat up the Display. I layed the Blow Dryer on the Counter turned it on and Held the phone up to it. Thinking if my fingers get too hot chances are it is too hot for the Display too.. :) Might be a little incaccurate to read the temperature like that but hey it worked. But soon after I started to remove the first pieces of broken glass I ran into Problems.
As per instructions I found, I put a Piece of tape accros the Screen so that the individuall pieces stayed ogether. That did not work at all for me. It just made the individual pieces push against the valuable digitizer below it. My next Problem was that the Tools that came with the replacement glass, especially the Little plastic Tools did not hold up to the Job und the tip was soon useless. I had to Switch to a Raizor blade. A couple of times I sliped and hit the Digitizer. Thinking oh well I guess I Need to get a new one. Luckely on the end it all worked out much better then I would have hoped. The left over glue I rubbed mostly off with my finger which worked out nicely. To clean it completely from ist glue took some time. The black rubber allong the side of the phone allso suffered. You might want to look out that that does not get riped out completely. I had enough left over so that the glass would sit on it good enough luckely.
Take a look at these Pictures and remember it works perfectly again for $9. While it is not for everyone to seperate a Glass from a Digitizer it is acctualy less fragile as you might think. The third Picture Shows you how it looked with all the scuff marks from taking off the glass. You can still see a few little marks on the end but hard to notice and much better then before. I am sure next time I will be more carefull and use the blade from the beginning on.
I got more Pictures and will improve this Thread for others that have to go through it. Feel free to PM me if you have any Questions. A list of other resources will also be included. This is only to explain and Show the bare state.