Hey friends,
the leaked jelly bean is out for our beloved s3.!!
check from the link. Hit thanks if I helped you :D
http://www.sammobile.com/2013/05/20/...-galaxy-s-iii/
----
New enhancements in Android 4.2.2 update
- Android 4.2.2 Build ID: JDQ39
- New S4 Lockscreen: Multiple Widgets, two Unlock effects (Ripple and Light), improved ripple effect than Android 4.1.2, ability to change clock size and set a personal message
- New Screen modes (From S4): Adapt Display and Professional Photo
- Daydream
- Driving mode
- Actionable notifications
- New Additions in Notification Center
- Completely revamped Settings UI (Tabbed interface Exactly like the S4)
- Addition of Voice controls (Lets you control various parts of the phone using voice commands Galaxy S4 feature)
- Gallery modes have white background (When changing gallery modes to 3D the background changes to white)
- Full screen Samsung apps
- New S-Voice (from S4)
- New smart switch widget
- Found more? Tell us about them in the comments below!
WARNINGS
- This firmware will increase your binary counter but the current binary and system status will remain official.
- We have re-packaged this firmware from dump files.
- There is no modem in this firmware, so the Modem you will be using before flashing this firmware will remain the same.
- This is a pre-release firmware and not official from Samsung.
- We have fully tested this firmware and this firmware works perfectly as any other official firmware.
Firmware Details
Android Version: 4.2.2 JDQ39 (Jelly Bean)
PDA: I9300XXUFME3
CSC: I9300OJKFME1
MODEM: N/A
Region: Middle East
Carrier: Branded
Changelist: 611730
Build Date: 8 May 2013
Download: I9300XXUFME3_I9300OJKFME1_ILO.zip
Flashing Instructions
- Unzip the file
- Open Odin 3.04 (already included in the firmware package)
- Restart phone in download mode (Press and hold Home + Power + Volume down buttons)
- Connect phone and wait until you get a blue sign in Odin
- Add I9300XXUFME3_I9300OJKFME1_HOME.tar.md5 to PDA
- Make sure re-partition is NOT ticked
- Start flash, sit back and wait a few minutes.
- If you encounter any issues with the firmware (Any FC, Bootloop etc)
- Boot into recovery mode (Home+power+vol up)
- Choose to wipe/factory reset. (THIS WILL ERASE ALL OF YOUR DATA INCLUDING YOUR INTERNAL SD CARD!)
- Then choose reboot and you should be good to go!
the leaked jelly bean is out for our beloved s3.!!
check from the link. Hit thanks if I helped you :D
http://www.sammobile.com/2013/05/20/...-galaxy-s-iii/
----
New enhancements in Android 4.2.2 update
- Android 4.2.2 Build ID: JDQ39
- New S4 Lockscreen: Multiple Widgets, two Unlock effects (Ripple and Light), improved ripple effect than Android 4.1.2, ability to change clock size and set a personal message
- New Screen modes (From S4): Adapt Display and Professional Photo
- Daydream
- Driving mode
- Actionable notifications
- New Additions in Notification Center
- Completely revamped Settings UI (Tabbed interface Exactly like the S4)
- Addition of Voice controls (Lets you control various parts of the phone using voice commands Galaxy S4 feature)
- Gallery modes have white background (When changing gallery modes to 3D the background changes to white)
- Full screen Samsung apps
- New S-Voice (from S4)
- New smart switch widget
- Found more? Tell us about them in the comments below!
WARNINGS
- This firmware will increase your binary counter but the current binary and system status will remain official.
- We have re-packaged this firmware from dump files.
- There is no modem in this firmware, so the Modem you will be using before flashing this firmware will remain the same.
- This is a pre-release firmware and not official from Samsung.
- We have fully tested this firmware and this firmware works perfectly as any other official firmware.
Firmware Details
Android Version: 4.2.2 JDQ39 (Jelly Bean)
PDA: I9300XXUFME3
CSC: I9300OJKFME1
MODEM: N/A
Region: Middle East
Carrier: Branded
Changelist: 611730
Build Date: 8 May 2013
Download: I9300XXUFME3_I9300OJKFME1_ILO.zip
Flashing Instructions
- Unzip the file
- Open Odin 3.04 (already included in the firmware package)
- Restart phone in download mode (Press and hold Home + Power + Volume down buttons)
- Connect phone and wait until you get a blue sign in Odin
- Add I9300XXUFME3_I9300OJKFME1_HOME.tar.md5 to PDA
- Make sure re-partition is NOT ticked
- Start flash, sit back and wait a few minutes.
- If you encounter any issues with the firmware (Any FC, Bootloop etc)
- Boot into recovery mode (Home+power+vol up)
- Choose to wipe/factory reset. (THIS WILL ERASE ALL OF YOUR DATA INCLUDING YOUR INTERNAL SD CARD!)
- Then choose reboot and you should be good to go!